Title

Extreme Chirped Pulse Modelocked Diode Laser Ring Oscillator Using A Theta Cavity Design

Abstract

We demonstrate an extreme chirped pulse modelocked laser, simultaneously generating near-transform-limited 3.6 psec optical pulses and a 510 psec linearly chirped output. The design overcomes fundamental limitations of energy extraction and nonlinearities induced by gain dynamics. High energy short pulse lasers play important roles in industry including remote sensing and material processing. Even though the semiconductor laser has many attractive advantages, such as compactness, mass productivity, cost effectiveness and excellent wall-plug efficiency, the use of semiconductor lasers in high power applications has been limited by their small energy storage time, as compared to other gain mediums. However, most recently, we have developed the extreme chirped pulse amplification system that generates 1.4 kW of peak power from an all-semiconductor master oscillator and power amplifier (MOPA) system to overcome the small energy storage time of semiconductor lasers [1], This summary describes a novel extreme chirped pulse laser oscillator that generates a periodic linearly chirped cw ouput and ultrashort pulses, simultaneously. One of key advantages of this laser system is the absence of self-phase modulation in the semiconductor optical amplifier (SOA). In this operation regime, the modelocked pulses are temporally stretched to a temporal duration that equals the pulse repetition period, converting the pulse train into a cw signal. By amplifying this cw signal in the semiconductor optical amplifier, the detrimental effects of transient gain saturation and integrating self phase modulation are eliminated [2, 3]. Recently, a 'free-space' breathing mode dispersion managed modelocked diode ring laser has been demonstrated, that uses the ideas of intracavity temporal pulse shape management to minimize nonlinearities in the semiconductor gain [4, 5]. The extreme chirped pulse modelocked oscillator is an evolution of the dispersion managed oscillator, but with a new key advantage. The pulse repetition period of the modelocked oscillator can be adjusted to be longer that the gain recovery time. In this case, since the gain dynamics of the SOA behaves in the cw regime, the limitation to the extracted pulse energy under transient optical amplification can be overcome. As a result, the output power of the laser can be increase by increasing the DC current, without concern of the gain saturation and nonlinearities induced by the transient gain dynamics. Finally, the present embodiment is comprised of all fiber components, providing compactness, and facilitating its use. The theta laser schematic is shown in Fig. 1. An SOA is inserted in an external cavity incorporating a chirped fiber bragg grating (CFBG), having a dispersion of 340 ps/nm, and a 20 GHz modulator. The single CFBG is used as a stretcher and a compressor in order to minimize the total group delay ripple. We use a low loss 20 GHz modulator and a tunable band pass filter having 5 nm FWHM to prevent a closed loop cw lasing of transmitted power. A 50 GHz electrical comb source is utilized to provide a short time window in active modelocking. The electrical pulse is amplified by use of a broadband modulator driver to achieve a sufficient modulation index. The laser is modulated at 1.951 GHz, generating periodic pulses separated by 510 psec. To demonstrate the operation of the modelocked oscillator, Fig. 2 shows low resolution spectrally resolved streak camera traces from the two different output ports of the laser. Fig. 2 (a) shows the spectrogram of the output port that generates modelocked pulses. Well defined pulses are observed with a pulse period of 510 psec. Fig. 2 (b) shows the output from the port that generates the periodic linearly chirped cw signal. Note in this figure, the true cw nature of the output. To obtain a more accurate measure of the temporal and spectral characteristics, Fig. 3 shows a sampling scope trace, an intensity autocorrelation and optical spectrum. The sampling scope trace (Fig. 3 (a)) shows resolution limited optical pulses separated at 510 psec. Fig. 3 (b, c) show the intensity autocorrelation trace and the optical spectrum measured at the three different DC bias currents to the SOA. The generated optical pulses are near the transform limited, with a pulse duration of 3.6 psec (FWHM) and a spectral bandwidth of 1.5 nm. Note that the pulse quality and optical spectrum maintain their general characteristics spanning a pumping current range of -4X the threshold current. In conclusion, we demonstrate a novel optical cavity design to realize an extreme chirped pulse modelocked laser. The novel ring, or theta cavity, generates near transform limited 3.6 psec modelocked optical pulses and a periodic 510 psec linearly chirped cw output, spanning 1.5 nm. The novel cavity design is used to overcome the limited energy extraction and nonlinearities induced by the transient gain dynamics in modelocked semiconductor lasers. In this experiment, we get 13.3 mW of average power at 600 mA in stretched port. These results show the extreme chirped pulse modelocked laser for the potential use of a master oscillator in high power applications. © 2005 IEEE.

Publication Date

1-1-2005

Publication Title

Conference Proceedings - Lasers and Electro-Optics Society Annual Meeting-LEOS

Volume

2005

Number of Pages

649-650

Document Type

Article; Proceedings Paper

Personal Identifier

scopus

DOI Link

https://doi.org/10.1109/LEOS.2005.1548164

Socpus ID

33751314323 (Scopus)

Source API URL

https://api.elsevier.com/content/abstract/scopus_id/33751314323

This document is currently not available here.

Share

COinS